Yamaha DragStar XVS650A Скачать руководство пользователя

Страница: 68 / 86

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

EAU24360

Front wheel

EAU24660

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Disconnect the speedometer ca-

ble from the front wheel.

2. Loosen the front wheel axle pinch

bolt.

3. Remove the rubber cap, and then

loosen the wheel axle.

4. Lift the front wheel off the ground

according to the procedure on
page 6-30.

5. Pull the wheel axle out, and then

remove the wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAU24921

To install the front wheel

1. Install the speedometer gear unit

into the wheel hub so that the pro-
jections mesh with the slots.

2. Lift the wheel up between the fork

legs.

NOTE:

Make sure that there is enough space
between the brake pads before insert-
ing the brake disc and that the slot in
the speedometer gear unit fits over the
retainer on the fork leg.

3. Insert the wheel axle.
4. Lower the front wheel so that it is

on the ground.

1. Speedometer cable

1. Rubber cap
2. Wheel axle

3. Front wheel axle pinch bolt

1. Speedometer gear unit
2. Speedometer cable

3. Retainer

U5SCE1E0.book Page 31 Monday, September 8, 2003 11:32 AM

Содержание DragStar XVS650A























































































Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды

Yamaha DragStar XVS650A, Руководство пользователя

Результаты поиска

Содержание DragStar XVS650A

Отзывы:

Похожие инструкции для DragStar XVS650A

Бренды по названию

Популярные бренды