Yamaha 2009 XV250Y Скачать руководство пользователя

Страница: 67 / 84

PERIODIC MAINTENANCE AND ADJUSTMENT

7-32

EAU24360

Front wheel

EAU24601

To remove the front wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Disconnect the speedometer ca-

ble from the front wheel.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle.

3. Lift the front wheel off the ground

according to the procedure on
page 7-31.

4. Pull the wheel axle out, and then

remove the wheel.

NOTICE:

not apply the brake after the
wheel has been removed to-
gether with the brake disc, oth-
erwise the brake pads will be
forced shut.

[ECA11071]

EAU24932

To install the front wheel

1. Install the speedometer gear unit

into the wheel hub so that the pro-
jections mesh with the slots.

2. Lift the wheel up between the fork

legs.

TIP

Make sure that there is enough space
between the brake pads before insert-
ing the brake disc and that the slot in
the speedometer gear unit fits over the
retainer on the fork leg.

1. Speedometer cable

1. Wheel axle
2. Front wheel axle pinch bolt

1. Speedometer gear unit

U2UJ26E0.book Page 32 Thursday, May 22, 2008 10:21 AM

Содержание 2009 XV250Y





















































































Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды

Yamaha 2009 XV250Y, Руководство пользователя

Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды