Yamaha 2009 XV250Y Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 84

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-18

7

1. Loosen the locknut at the brake

pedal.

2. To raise the brake pedal, turn the

adjusting bolt in direction (a). To
lower the brake pedal, turn the ad-
justing bolt in direction (b).

3. Tighten the locknut.

WARNING

EWA11230

After adjusting the brake pedal posi-
tion, the brake pedal free play must
be adjusted.

Brake pedal free play

The brake pedal free play should mea-
sure 20.0–30.0 mm (0.79–1.18 in) at
the brake pedal end. Periodically check
the brake pedal free play and, if neces-
sary, adjust it as follows.
To increase the brake pedal free play,
turn the adjusting nut at the brake rod in
direction (a). To decrease the brake
pedal free play, turn the adjusting nut in
direction (b).

WARNING

EWA10680

●

After adjusting the drive chain
slack or removing and installing
the rear wheel, always check the
brake pedal free play.

●

If proper adjustment cannot be
obtained as described, have a
Yamaha dealer make this ad-
justment.

●

After adjusting the brake pedal
free play, check the operation of
the brake light.

1. Locknut
2. Brake pedal position adjusting bolt

1. Brake pedal free play adjusting nut

U2UJ26E0.book Page 18 Thursday, May 22, 2008 10:21 AM

«
...
51
52
53
54
55
...
»

Содержание 2009 XV250Y





















































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 XV250Y

Бренд: Uclear Страницы: 2

Бренд: Baja motorsports Страницы: 20

Бренд: Yoshimura Страницы: 7

ST400 Cruiser Edition

Бренд: STEEL HORSE AUDIO Страницы: 6

Бренд: Ducati Страницы: 123

Бренд: Nolan Страницы: 80

Daytona 955i 2002

Бренд: Triumph Страницы: 384

Бренд: Memphis Shades Страницы: 2

Бренд: CATU Страницы: 6

Бренд: CATU Страницы: 8

Бренд: JAWA Страницы: 22

TOPMASTER VOZP59ST

Бренд: Shad Страницы: 2

F12R AIR 50 cc. - Euro 2

Бренд: Malaguti Страницы: 46

XSM POWER UP 2007

Бренд: Malaguti Страницы: 53

Бренд: Piaa Страницы: 17

Бренд: Protekt Страницы: 4

Бренд: R&G Страницы: 9

2014 1190 Adventure

Бренд: KTM Страницы: 228

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды