Yamaha 2009 XV250Y Скачать руководство пользователя

Страница: 60 / 84

PERIODIC MAINTENANCE AND ADJUSTMENT

7-25

EAUM1650

Lubricating the swingarm piv-
ots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

EAU23272

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

WARNING! To avoid injury,

securely support the vehicle so
there is no danger of it falling
over.

[EWA10751]

2. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

NOTICE

ECA10590

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.

Recommended lubricant:

Lithium-soap-based grease

U2UJ26E0.book Page 25 Thursday, May 22, 2008 10:21 AM

Содержание 2009 XV250Y





















































































Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды

Yamaha 2009 XV250Y, Руководство пользователя

Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды