Yamaha 2009 XV250Y Скачать руководство пользователя

Страница: 46 / 84

PERIODIC MAINTENANCE AND ADJUSTMENT

7-11

3. Remove the air filter case cover by

removing the screws.

4. Remove the air filter element by

removing the wing nut.

5. Remove the sponge material from

the air filter element frame, clean it
with solvent, and then squeeze the
remaining solvent out.

WARNING!

Use only a dedicated parts
cleaning solvent. To avoid the
risk of fire or explosion, do not
use gasoline or solvents with a
low flash point.

[EWA10431]

NOTICE:

To avoid damaging the foam
material, handle it gently and
carefully, and do not twist or
wring it.

[ECA10511]

6. Apply oil of the recommended type

to the entire surface of the sponge
material, and then squeeze the ex-
cess oil out.

TIP

The air filter element should be wet but
not dripping.

7. Pull the sponge material over the

air filter element frame.

8. Insert the element into the air filter

case, and then tighten the wing
nut.

NOTICE:

Make sure that the

air filter element is properly
seated in the air filter case. The

1. Screw

1. Wing nut

2. Air filter element

1. Sponge material
2. Air filter element frame

Recommended oil:

Yamaha foam air filter oil or other
quality foam air filter oil

U2UJ26E0.book Page 11 Thursday, May 22, 2008 10:21 AM

Содержание 2009 XV250Y





















































































Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды

Yamaha 2009 XV250Y, Руководство пользователя

Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды