Yamaha 2009 XV250Y Скачать руководство пользователя | Manualshive

Страница: 51 / 84

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-16

7

EAU22041

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the clutch le-

ver.

2. To increase the clutch lever free

play, turn the adjusting bolt in di-
rection (a). To decrease the clutch
lever free play, turn the adjusting
bolt in direction (b).

TIP

If the specified clutch lever free play
could be obtained as described above,
tighten the locknut and skip the rest of
the procedure, otherwise proceed as
follows.

3. Fully turn the adjusting bolt at the

clutch lever in direction (a) to loos-
en the clutch cable.

4. Loosen the locknut at the crank-

case.

5. To increase the clutch lever free

play, turn the adjusting nut in direc-
tion (a). To decrease the clutch le-
ver free play, turn the adjusting nut
in direction (b).

6. Tighten the locknut at the clutch le-

ver and the crankcase.

1. Locknut

2. Clutch lever free play adjusting bolt
3. Clutch lever free play

1. Locknut

2. Clutch lever free play adjusting nut (crank-

case)

U2UJ26E0.book Page 16 Thursday, May 22, 2008 10:21 AM

«
...
49
50
51
52
53
...
»

Содержание 2009 XV250Y





















































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 XV250Y

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Бренд: 3M Страницы: 84

Бренд: APRILIA Страницы: 9

Бренд: Suzuki Страницы: 151

Бренд: Sachs Bikes Страницы: 84

Бренд: Two Brothers Racing Страницы: 2

Бренд: dushi Страницы: 4

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

SCARABEO 300 SPECIAL

Бренд: APRILIA Страницы: 157

PEGASO 650 IE - 2004

Бренд: APRILIA Страницы: 96

DORSODURO 750 -

Бренд: APRILIA Страницы: 7

ATLANTIC 500 sprint

Бренд: APRILIA Страницы: 161

Бренд: APRILIA Страницы: 302

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 6

Бренд: R&G Страницы: 8

Бренд: R&G Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды