Yamaha 2009 XV250Y Скачать руководство пользователя страница 25

Страница: 25 / 84

INSTRUMENT AND CONTROL FUNCTIONS

4-9

To unlock the steering

1. Open the steering lock cover, and

then insert the key.

2. Push the key in, turn it 1/8 turn

counterclockwise so that it moves
out, and then release it.

3. Remove the key, and then close

the lock cover.

EAU14220

Rider seat

To remove the rider seat

Remove the bolts, and then pull the rid-
er seat off.

To install the rider seat

1. Insert the projection on the front of

the rider seat into the seat holder
as shown.

2. Place the rider seat in the original

position, and then tighten the bolts.

TIP

Make sure that the rider seat is properly
secured before riding.

1. Bolt

1. Projection
2. Seat holder

U2UJ26E0.book Page 9 Thursday, May 22, 2008 10:21 AM

Содержание 2009 XV250Y





















































































Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды

Yamaha 2009 XV250Y, Руководство пользователя

Результаты поиска

Содержание 2009 XV250Y

Отзывы:

Похожие инструкции для 2009 XV250Y

Бренды по названию

Популярные бренды