Yamaha 2006 FZ6-S Скачать руководство пользователя

Страница: 77 / 94

PERIODIC MAINTENANCE AND MINOR REPAIR

6-37

NOTE:

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

6. While supporting the brake caliper

and slightly lifting the wheel, pull
the wheel axle out.

NOTE:

A rubber mallet may be useful to tap the
wheel axle out.

7. Remove the wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAU34430

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the right-hand side.

NOTE:

●

Make sure that the retainer on the
swingarm is inserted into the slot in
the brake caliper bracket.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

2. Install the drive chain onto the rear

sprocket.

3. Install the axle nut, and then lower

the rear wheel so that it is on the
ground.

4. Adjust the drive chain slack. (See

page 6-22.)

5. Tighten the axle nut to the speci-

fied torque.

1. Wheel axle

2. Drive chain slack adjusting nut
3. Locknut

4. Brake caliper bracket

5. Brake caliper

1. Retainer
2. Slot

Tightening torque:

Axle nut:

120 Nm (12.0 m·kgf, 85 ft·lbf)

U1B3E3E0.book Page 37 Friday, July 14, 2006 11:34 AM

Содержание 2006 FZ6-S































































































Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды

Yamaha 2006 FZ6-S, Руководство пользователя

Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды