Yamaha 2006 FZ6-S Скачать руководство пользователя | Manualshive

Страница: 82 / 94

background image

MOTORCYCLE CARE AND STORAGE

7-2

7

cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.

●

Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

●

For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.

After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.

After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.

NOTE:

Salt sprayed on roads in the winter may
remain well into spring.

1. Clean the motorcycle with cold wa-

ter and a mild detergent, after the
engine has cooled down.

CAUTION:

ECA10790

Do not use warm water since it in-
creases the corrosive action of the
salt.

2. After drying the motorcycle, apply

a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.

After cleaning

1. Dry the motorcycle with a chamois

or an absorbing cloth.

2. Immediately dry the drive chain

and lubricate it to prevent it from
rusting.

3. Use a chrome polish to shine

chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)

U1B3E3E0.book Page 2 Friday, July 14, 2006 11:34 AM

«
...
80
81
82
83
84
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Бренд: R&G Страницы: 8

Бренд: Crivit Страницы: 70

Бренд: X-lite Страницы: 100

STAR XV19CSX(C)

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 100

Star XV250B 2011

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 120

Бренд: Menuett Страницы: 27

Бренд: Baotian Страницы: 22

Бренд: KFI Страницы: 2

TORNADO Tre Novecento 900

Бренд: Benelli Страницы: 48

Бренд: Benelli Страницы: 108

Бренд: Beta Страницы: 38

Бренд: Beta Страницы: 60

Бренд: Beta Страницы: 68

Бренд: Beta Страницы: 81

Бренд: hepco & becker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды