Yamaha 2006 FZ6-S Скачать руководство пользователя

Страница: 50 / 94

PERIODIC MAINTENANCE AND MINOR REPAIR

6-10

NOTE:

After the engine is started, the engine
oil level warning light should go off if the
oil level is sufficient.

CAUTION:

ECA10400

If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha dealer
check the vehicle.

10. Turn the engine off, and then

check the oil level and correct it if
necessary.

EAU20070

Coolant

The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.

EAU20091

To check the coolant level

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

NOTE:

●

The coolant level must be checked
on a cold engine since the level
varies with engine temperature.

●

Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.

2. Check the coolant level in the cool-

ant reservoir.

NOTE:

The coolant should be between the
minimum and maximum level marks.

3. If the coolant is at or below the

minimum level mark, remove the
reservoir cap.

1. Coolant reservoir
2. Maximum level mark

3. Minimum level mark

1. Coolant reservoir cap

U1B3E3E0.book Page 10 Friday, July 14, 2006 11:34 AM

Содержание 2006 FZ6-S































































































Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды

Yamaha 2006 FZ6-S, Руководство пользователя

Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды