Yamaha 2006 FZ6-S Скачать руководство пользователя | Manualshive

Страница: 59 / 94

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-19

6

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU22080

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the adjusting bolt in direction (a).
To decrease the clutch lever free play,
turn the adjusting bolt in direction (b).

NOTE:

If the specified free play cannot be ob-
tained as described above or if the
clutch does not operate correctly, have
a Yamaha dealer check the internal
clutch mechanism.

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

U1B3E3E0.book Page 19 Friday, July 14, 2006 11:34 AM

«
...
57
58
59
60
61
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Бренд: Honda Страницы: 118

ZTechnik VStream Z2392

Бренд: National Cycle Страницы: 2

Бренд: Honda Страницы: 26

Бренд: Kabuto Страницы: 6

HPS.08.473.10000/B

Бренд: SW-Motech Страницы: 4

Бренд: DYNATEK Страницы: 12

Бренд: hepco & becker Страницы: 3

Бренд: AGUSTA Страницы: 427

Бренд: Shark Страницы: 8

Бренд: Aosom Страницы: 25

Fast Time F-10 50cc

Бренд: Malaguti Страницы: 151

Бренд: JAWA Страницы: 40

Бренд: Yamaha Страницы: 27

Бренд: Yamaha Страницы: 71

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды