background image

INSTRUMENT AND CONTROL FUNCTIONS

3-10

3

EAU12347

Handlebar switches 

Left

Right

EAU12350

Pass switch “

” 

Press this switch to flash the headlight.

EAU12400

Dimmer switch “

/

” 

Set this switch to “

” for the high

beam and to “

” for the low beam.

EAU12460

Turn signal switch “

/

” 

To signal a right-hand turn, push this
switch to “

”. To signal a left-hand

turn, push this switch to “

”. When re-

leased, the switch returns to the center

position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.

EAU12500

Horn switch “

” 

Press this switch to sound the horn.

EAU12660

Engine stop switch “

/

” 

Set this switch to “

” before starting

the engine. Set this switch to “

” to

stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.

EAU12710

Start switch “

” 

Push this switch to crank the engine
with the starter.

CAUTION:

ECA10050

See page 5-1 for starting instruc-
tions prior to starting the engine.

EAU41700

The engine trouble warning light will
come on when the key is turned to “ON”
and the start switch is pushed, but this
does not indicate a malfunction.

1. Pass switch “

2. Dimmer switch “

/

3. Turn signal switch “

/

4. Horn switch “

5. Hazard switch “

1. Engine stop switch “

/

2. Start switch “

U1B3E3E0.book  Page 10  Friday, July 14, 2006  11:34 AM

Содержание 2006 FZ6-S































































































Отзывы: