Yamaha 15D Скачать руководство пользователя | Manualshive

Страница: 47 / 64

background image

Maintenance

42

1.

Apply Yamaha marine grease or a corro-
sion resistant grease to the propeller
shaft.

2.

Install the spacer(if equipped), thrust
washer, and propeller on the propeller
shaft.

3.

Install the spacer (if equipped) and the
washer. Tighten the propeller nut to the
specified torque.

4.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTE:

If the propeller nut does not align with the pro-
peller shaft hole after tightening to the speci-
fied torque, tighten the nut further to align it
with the hole.

EMU29280

Changing gear oil

WARNING

EWM00800

●

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

●

Never get under the lower unit while it is
tilted, even when the tilt support lever or
knob is locked. Severe injury could oc-
cur if the outboard motor accidentally
falls.

1.

Tilt the outboard motor so that the gear oil
drain screw is at the lowest point possi-
ble.

2.

Place a suitable container under the gear
case.

3.

Remove the gear oil drain screw.

NOTE:

If the magnetic gear oil drain screw equipped:
remove all metal particles from the screw be-
fore installing it.

4.

Remove the oil level plug to allow the oil
to drain completely.

CAUTION:

ECM00710

Inspect the used oil after it has been
drained. If the oil is milky, water is getting
into the gear case which can cause gear
damage. Consult a Yamaha dealer for re-
pair of the lower unit seals.

NOTE:

For disposal of used oil consult your Yamaha
dealer.

5.

With the outboard motor in a vertical po-
sition, and using a flexible or pressurized
filling device, inject the gear oil into the
gear oil drain screw hole.

1. Gear oil drain screw
2. Oil level plug

ZMU02064

2

1

U63V17E0.book Page 42 Thursday, February 26, 2004 11:52 AM

«
...
45
46
47
48
49
...
»

Содержание 15D

































































Отзывы:

Нет отзывов

Похожие инструкции для 15D

Бренд: IEI Technology Страницы: 234

Бренд: Gigabyte Страницы: 125

Бренд: DFI Страницы: 99

Бренд: Texas Instruments Страницы: 101

S1V30080 Series

Бренд: Seiko Epson Страницы: 10

Бренд: NXP Semiconductors Страницы: 28

Бренд: NXP Semiconductors Страницы: 16

Бренд: AKM Страницы: 30

Бренд: Supero Страницы: 107

Бренд: Biostar Страницы: 118

Бренд: Microchip Technology Страницы: 89

Бренд: Advantech Страницы: 88

SR1500AL - Server System - 0 MB RAM

Бренд: Intel Страницы: 180

Бренд: Gigabyte Страницы: 72

Бренд: Zamel Страницы: 3

Бренд: Gigabyte Страницы: 2

Бренд: Ublox Страницы: 20

Бренд: Laird Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды