Yamaha 15D Скачать руководство пользователя | Manualshive

Страница: 54 / 64

background image

Trouble Recovery

49

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
cord where it could become entangled,
preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could
cause people and objects in the boat to
be thrown forward.

●

Be sure no one is standing behind you
when pulling the starter rope. It could
whip behind you and injure someone.

●

An unguarded, rotating flywheel is very
dangerous. Keep loose clothing and
other objects away when starting the en-
gine. Use the emergency starter rope
only as instructed. Do not touch the fly-
wheel or other moving parts when the
engine is running. Do not install the
starter mechanism or top cowling after
the engine is running.

●

Do not touch the ignition coil, spark plug
wire, spark plug cap, or other electrical
components when starting or operating
the motor. You could get an electrical
shock.

EMU29561

Emergency starting engine

1.

Remove the top cowling.

2.

Remove the start-in-gear protection ca-
ble from the starter, if equipped.

3.

Remove the starter/flywheel cover after
removing the bolt(s).

4.

Prepare the engine for starting. For fur-
ther information, see page 22. Be sure
the engine is in neutral and that the en-
gine stop switch lanyard lock plate is at-
tached to the engine stop switch. The
main switch must be “

” (on), if

equipped.

5.

If equipped the choke knob, pull out it
when the engine is cold. After the engine
starts, gradually return the choke knob to
its home position as the engine warms
up.

6.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope several turns
around the flywheel clockwise.

7.

Give a strong pull straight out to crank
and start the engine. Repeat if neces-
sary.

U63V17E0.book Page 49 Thursday, February 26, 2004 11:52 AM

«
...
52
53
54
55
56
...
»

Содержание 15D

































































Отзывы:

Нет отзывов

Похожие инструкции для 15D

Бренд: Yanmar Страницы: 44

Бренд: ECS Страницы: 72

RHINO VAP133-ACP

Бренд: Octek Страницы: 66

Бренд: AKM Страницы: 45

Бренд: WIN Enterprises Страницы: 82

Бренд: JETWAY Страницы: 58

Бренд: Gigabyte Страницы: 72

Z87 Extreme9/ac

Бренд: ASROCK Страницы: 116

Бренд: Ublox Страницы: 32

Бренд: JETWAY Страницы: 60

SIDE POWER SRH 240 TC

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: Avalue Technology Страницы: 92

Бренд: NXP Semiconductors Страницы: 7

DS320PR412-421EVM

Бренд: Texas Instruments Страницы: 31

Бренд: Gigabyte Страницы: 2

NuPRO-590 Series

Бренд: ADLINK Technology Страницы: 85

Бренд: Gan Systems Страницы: 22

Бренд: Linear Technology Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды