Yamaha 15D Скачать руководство пользователя | Manualshive

Страница: 27 / 64

background image

Operation

22

EMU27490

Starting engine

EMU27530

Manual start models

1.

Place the gear shift lever in neutral.

NOTE:

The start-in-gear protection device prevents
the engine from starting except when in neu-
tral.

2.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

EWM00120

●

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could
cause people and objects in the boat to
be thrown forward.

3.

Place the throttle grip in the “

”

(start) position.

4.

Pull out / turn the choke knob fully. Place
the choke knob back in to the second or
third position to warm up the engine after
starting. When the engine has fully
warmed up, replace the choke knob back
in to its home position.

ZMU02025

U63V17E0.book Page 22 Thursday, February 26, 2004 11:52 AM

«
...
25
26
27
28
29
...
»

Содержание 15D

































































Отзывы:

Нет отзывов

Похожие инструкции для 15D

Бренд: ZiLOG Страницы: 41

Бренд: BESTEK Страницы: 52

Бренд: ST Страницы: 13

Бренд: TYAN Страницы: 90

B85-IE35 Series

Бренд: MSI Страницы: 190

Бренд: Supero Страницы: 90

Бренд: Texas Instruments Страницы: 14

Бренд: Honda Страницы: 152

Бренд: MSI Страницы: 126

E-TEC 40RL 2008

Бренд: Evinrude Страницы: 58

MBD-X11SDV-4C-TP8F-B

Бренд: Supermicro Страницы: 123

Бренд: Peak Страницы: 33

EVAL-AD2428WD1BZ

Бренд: Analog Devices Страницы: 6

Бренд: JETWAY Страницы: 50

Бренд: Linear Technology Страницы: 8

Бренд: MSI Страницы: 58

Бренд: Acorp Страницы: 26

Бренд: DFI Страницы: 93

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды