Yamaha 15D Скачать руководство пользователя

Страница: 41 / 64

Maintenance

ger the operator and passengers. Yamaha
genuine parts and accessories are available
from your Yamaha dealer.

EMU28521

Maintenance chart

Frequency of maintenance operations may be adjusted according to the operating conditions,
but the following table gives general guidelines. Refer to the sections in this chapter for expla-
nations of each owner-specific action.
The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

NOTE:

When operating in salt water, turbid or muddy water, the engine should be flushed with clean
water after each use.

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

(3 months)

100 hours

(6 months)

200 hours

(1 year)

Anode(s) (external)

Inspection /
replacement

Anode(s) (internal)

Inspection /
replacement

Cooling water
passages

Cleaning

Cowling clamp

Inspection

Fuel filter (can be
disassembled)

Inspection / cleaning

Fuel system

Inspection

Fuel tank (Yamaha
portable tank)

Inspection / cleaning

Gear oil

Change

Greasing points

Greasing

Idling speed
(carburetor models)

Inspection / adjustment

Propeller and cotter pin

Inspection /
replacement

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection

Throttle link / throttle
cable / throttle pick-up
timing

Inspection / adjustment

Water pump

Inspection

Spark plug(s)

Cleaning / adjustment /
replacement

U63V17E0.book Page 36 Thursday, February 26, 2004 11:52 AM

Содержание 15D

































































Результаты поиска

Содержание 15D

Отзывы:

Похожие инструкции для 15D

Бренды по названию

Популярные бренды

Yamaha 15D, Руководство пользователя

Результаты поиска

Содержание 15D

Отзывы:

Похожие инструкции для 15D

Бренды по названию

Популярные бренды