Yamaha 15D Скачать руководство пользователя

Страница: 16 / 64

Basic components

EMU25830

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU25911

Tiller handle

To change direction, move the tiller handle to
the left or right as necessary.

EMU25922

Gear shift lever

Pulling the gear shift lever towards you puts
the engine in forward gear so that the boat
moves ahead. Pushing the lever away from
you puts the engine in reverse gear so that the
boat moves astern.

EMU25941

Throttle grip

The throttle grip is on the tiller handle. Turn
the grip counterclockwise to increase speed
and clockwise to decrease speed.

1. Fuel joint

2. Fuel gauge

3. Fuel tank cap

4. Air vent screw

ZMU02284

1. Forward “ ”

2. Neutral “ ”

3. Reverse “ ”

U63V17E0.book Page 11 Thursday, February 26, 2004 11:52 AM

Содержание 15D

































































Результаты поиска

Содержание 15D

Отзывы:

Похожие инструкции для 15D

Бренды по названию

Популярные бренды

Yamaha 15D, Руководство пользователя

Результаты поиска

Содержание 15D

Отзывы:

Похожие инструкции для 15D

Бренды по названию

Популярные бренды