manualshive.com logo in svg

Yamaha 15D, Руководство пользователя

Поделиться
Скачать
Yamaha 15D Скачать руководство пользователя страница 29

Operation

24

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the en-
gine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote 
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and firm-
ly from neutral to forward.

Remote control models
Pull up the neutral interlock trigger (if
equipped) and move the remote control lever
quickly and firmly from neutral to forward.

EMU27795

Reverse (manual tilt and hydro tilt 
models)

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Other-
wise the boat could become unstable,
which could result in loss of control and
an accident.

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

On models equipped with a tilt lock lever,
check that it is in the lock/down position.

ZMU02856

ZMU02030

ZMU02030

U63V17E0.book  Page 24  Thursday, February 26, 2004  11:52 AM

Содержание 15D

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды