Yale HSA3800 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 28

Yale HSA3800 Скачать руководство пользователя страница 6

Control unit

Plug the power adaptor

into the mains supply wall
socket and the other end
into the control unit.
• The batteries in the

control unit are
rechargeable and act as
a back-up in case of
power failure. They are
charged automatically
by the mains supply. If the mains supply is
disconnected, an AC Power Fail message will
be displayed and the LCD back light will be
switched off.

• From new, the batteries need 72 hours to

charge completely.

6

Unpack all the parts onto a table top

The easiest way to get to know the system and get it up and running quickly is to get
all the devices and accessories programmed on a table top before locating and mounting them.

2

Siren

WARNING: The siren is very loud, be

prepared!

Take care not to activate the siren

unnecessarily.

1

Remove the cover by unscrewing the single
screw located at the bottom.

2

Remove the covers of the two internal
compartments.

3

Insert the four D batteries as shown.
There is a slight pause while the unit initialises.
The siren will then beep and the LEDs flash.

Tamper
switch

Jumper

switches

Fixing holes
x 4

Downloaded from www.ukpanels.com

«
...
4
5
6
7
8
...
»

Содержание HSA3800





























Отзывы:

Нет отзывов