Yaesu FT-991A страница 139 Скачать руководство пользователя

Страница: 139 / 158

Page 137

FT-

991

Operating Manual

Menu Mode

095 RTTY HCUT SLOPE

Function: Sets the slope of the high-frequency cutoff au

dio filter in RTTY mode.

Available Values: 6dB/oct / 18dB/oct

Default Setting: 18dB/oct

Description: Selects the slope setting of the high-fre-

quency cutoff audio filter in RTTY mode.

096 RTTY SHIFT PORT

Function: Sets the SHIFT input jack for RTTY mode.

Available Values: SHIFT/DTR/RTS

Default Setting: SHIFT

Description: Selects the SHIFT input jack for RTTY

mode.

SHIFT: Inputs from the

RTTY/DATA

jack (pin 4)

on the rear panel.

DTR: Controls the signal from the USB virtual

COM/DTR ports.

RTS: Controls the signal from the USB virtual

COM/RTS ports.

097 RTTY POLARITY-RX

Function: Sets the shift direction for receiving in RTTY

mode.

Available Values: NOR/REV

Default Setting: NOR

Description: Sets the shift direction for receiving in

RTTY mode.

NOR: The space frequency will be lower than the

mark frequency.

REV: The mark frequency will be lower than the

space frequency.

098 RTTY POLARITY-TX

Function: Sets the shift direction for transmitting in

RTTY mode.

Available Values: NOR/REV

Default Setting: NOR

Description: Sets the shift direction for transmitting in

RTTY mode.

NOR: The space frequency will be lower than the

mark frequency.

REV: The mark frequency will be lower than the

space frequency.

099 RTTY OUT LEVEL

Function: Sets the output level during the sending/re-

ceiving of data in RTTY mode.

Available Values: 0 - 100

Default Setting: 50

Description: Sets the data output level during the send-

ing/receiving of data in RTTY mode. The

higher the setting, the higher the output

level becomes.

100 RTTY SHIFT FREQ

Function: Sets the shift width for RTTY mode.

Available Values: 170/200/425/850 (Hz)

Default Setting: 170Hz

Description: Sets the shift width for RTTY mode.

101 RTTY MARK FREQ

Function: Sets the mark frequency for RTTY mode.

Available Values: 1275/2125 (Hz)

Default Setting: 2125Hz

Description: Sets the mark frequency for RTTY mode.

102 SSB LCUT FREQ

Function: Sets the low-frequency cutoff audio filter in

SSB mode.

Available Values: OFF/100Hz - 1000Hz (50Hz/step)

Default Setting: 100Hz

Description: This is the low-frequency cutoff audio filter

in SSB mode.

The cutoff frequency can be set at 50 Hz

increments between 100 Hz and 1000 Hz.

103 SSB LCUT SLOPE

Function: Sets the slope of the low-frequency cutoff au

dio filter in SSB mode.

Available Values: 6dB/oct / 18dB/oct

Default Setting: 6dB/oct

Description: Selects the slope setting of the low-frequen-

cy cutoff audio filter in SSB mode.

104 SSB HCUT FREQ

Function: Sets the high-frequency cutoff audio filter in

SSB mode.

Available Values: OFF/700Hz - 4000Hz (50Hz/step)

Default Setting: 3000Hz

Description: This is the high-frequency cutoff audio fil

ter in SSB mode.

The cutoff frequency can be set at 50 Hz

increments between 700 Hz and 4000 Hz.

105 SSB HCUT SLOPE

Function: Sets the slope of the high-frequency cutoff au

dio filter in SSB mode.

Available Values: 6dB/oct / 18dB/oct

Default Setting: 6dB/oct

Description: Selects the slope setting of the high-fre-

quency cutoff audio filter in SSB mode.

106 SSB MIC SELECT

Function: Selects the microphone input jack for SSB

mode.

Available Values: MIC/REAR

Default Setting: MIC

Description: Selects the microphone input jack to be

used in SSB mode.

MIC: Inputs from the

MIC

jack on the front

panel.

REAR: Disables the microphone circuit on the

front panel and inputs from the

USB

jack

RTTY/DATA

jack on the rear panel.

Содержание FT-991A































































































































































Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды

Yaesu FT-991A, Руководство по эксплуатации

Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды