Yaesu FT-891 Скачать руководство пользователя страница 2

Страница: 2 / 114

Contents

FT-891 Advance Manual

CW Mode Operation ................................................. 3

Setup for Straight Key

(and Straight Key Emulation) Operation .... 3

Using the Built-in Electronic Keyer .......................... 4

Adjusting the keyer speed ....................................... 5

Full Break-in (QSK) Operation ................................. 5

Setting the Keyer Weight (Dot/Dash) Ratio ............. 6

Reversing the Keyer Polarity ................................... 6

Selecting the Keyer Operating Mode ....................... 7

CW Delay Time Setting ........................................... 8

CW Pitch Adjustment ............................................... 8

CW Spotting (Zero-Beating) .................................... 9

Using the Auto Zeroing System ............................ 9

Using the SPOT System ....................................... 9

Audio Peak Filter ................................................... 10

Contest Memory Keyer ...........................................11

Message Memory ................................................11

Text Memory ....................................................... 17

Contest Number Programming ........................... 23

Decrementing the Contest Number .................... 23

Transmitting in the Beacon Mode ....................... 24

FM Mode Operation ................................................ 25

Basic Operation ..................................................... 25

Repeater Operation ............................................... 26

Tone Squelch Operation ........................................ 27

DCS Operation ...................................................... 28

Interference Rejection ............................................ 29

CONTOUR Control Operation ............................... 29

WIDTH (IF DSP Bandwidth) Tuning

(SSB/CW/RTTY/DATA Modes) .... 30

Using IF SHIFT and WIDTH Together ................ 31

NARROW (NAR) One-Touch IF Filter Selection .... 31

IF NOTCH Filter Operation

(SSB/CW/RTTY/DATA/AM Modes) .... 32

Digital Noise Reduction (DNR) Operation ............. 33

Digital NOTCH Filter (DNF) Operation .................. 34

Tools for Comfortable and Effective Reception .. 35

RF Gain (SSB/CW/AM Modes) ............................. 35

ATT (Attenuator) .................................................... 35

IPO (Intercept Point Optimization) ......................... 36

AGC (Automatic Gain Control) .............................. 36

Adjustable Receiver Audio Filter ............................ 37

Enhancing Transmit Signal Quality ...................... 38

Mic Gain ................................................................ 38

Speech Processor (SSB Mode) ............................. 38

Parametric Microphone Equalizer

(SSB/AM mode) .... 39

Setup of the Parametric Microphone Equalizer .... 39

Activating the Parametric Microphone Equalizer .... 40

Adjusting the SSB Transmitted Bandwidth

(SSB Mode) .... 41

Transmitter Convenience Features....................... 42

Voice Memory (SSB/AM modes) ........................... 42

Voice Memory Operation .................................... 42

VOX (SSB/AM/FM Modes: Automatic

TX/RX Switching using Voice Control) .... 46

MONITOR (SSB/CW/AM modes) .......................... 47

Split Operation Using the TX Clarifier .................... 48

Split-Frequency Operation ..................................... 49

Quick Split Operation .......................................... 50

Memory Operation .................................................. 51

Checking a Memory Channel Status ..................... 51

Memory Tune (MT) operation ................................ 51

Labeling Memories ................................................ 52

Displaying the memory tag ................................ 52

Memory Groups ..................................................... 53

Memory Group Assignment ................................ 53

Choosing the Desired Memory Group ................ 54

Operation on Alaska Emergency Frequency:

5167.5 kHz (U.S. Version Only) .... 55

Scanning Operation ............................................... 56

Scan Resume Options ........................................... 56

PMS (Programmable Memory Scanning) .............. 57

Miscellaneous Setting ............................................ 58

Beep Level ............................................................. 58

TOT (Time-Out Timer) ........................................... 58

APO (Automatic Power Off) ................................... 59

FAN Control ........................................................... 59

Meter Peak Hold .................................................... 60

POP-UP Menu ....................................................... 60

Key Lamp Dimmer ................................................. 61

TX/BUSY Indicator Dimmer ................................... 61

RTTY (Radio Teletype) Operation ......................... 62

Example of Connecting RTTY

Communications device .... 62

Connecting to the TU (Terminal Unit) ................. 62

Connecting to your Computer ............................. 63

DATA (PSK) Operation ........................................... 64

Example of DATA Communications device ............ 64

DATA-AFSK (PSK, OLIVIA,

CONTESTIA, RTTY etc.) .... 65

DATA MODE (PSK, OLIVIA,

CONTESTIA, RTTY etc.) .... 67

Menu Mode .............................................................. 69

Optional FH-2 Remote Control Switches ........... 102

Optional MH-36E8J Microphone Switches ......... 103

FC-50 External Automatic Antenna Tuner .......... 104

Interconnections to FT-891 .................................. 104

Setup the FT-891 ................................................. 104

Operation ............................................................. 105

FC-40 External Automatic Antenna Tuner

(for Wire Antenna) .... 106

Interconnections to FT-891 .................................. 106

Setup the FT-891 ................................................. 107

Operation ............................................................. 107

Auto Active-Tuning Antenna System

(ATAS-120A) Operation .... 108

Interconnections to FT-891 .................................. 108

Setup the FT-891 ................................................. 109

Tuning Operation ................................................. 109

Manual Tuning ......................................................110

VL-1000 Linear Amplifier Interconnections ........111

Index ...................................................................... 112

Содержание FT-891


















































































































Результаты поиска

Содержание FT-891

Отзывы:

Бренды по названию

Популярные бренды

Yaesu FT-891, Руководство для продвинутых пользователей

Результаты поиска

Содержание FT-891

Отзывы:

Бренды по названию

Популярные бренды