Xyratex RS-1600-FC-SBD Скачать руководство пользователя

Страница: 56 / 82

RS-1600/1602-FC-SBD User Guide

3.2.1 Power Supply/Cooling Module LEDs

The Power Supply/Cooling module incorporates 4 LEDs, located below the On/Off switch and shown in

Table 3–1

• Under Normal conditions the LEDs should all be illuminated constant GREEN
• If a problem is detected the color of the relevant LED will change to AMBER.

3.3 Ops Panel LEDs

The Ops Panel LEDs status conditions are defined in

Table 3–2

and the LEDs are illustrated in

Figure 3–1

Table 3–1

PSU LEDs

AC PSU

-48V DC PSU

PSU Good

Green

PSU Good

Green

AC input Fail

Amber

Battery Fail

Amber

Fan Fault

Amber

Fan Fault

Amber

DC Output Fail

Amber

DC Output Fail

Amber

Figure 3–1

Ops Panel LEDs and Switches

Содержание RS-1600-FC-SBD



















































































Результаты поиска

Содержание RS-1600-FC-SBD

Отзывы:

Похожие инструкции для RS-1600-FC-SBD

Бренды по названию

Популярные бренды

Xyratex RS-1600-FC-SBD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание RS-1600-FC-SBD

Отзывы:

Похожие инструкции для RS-1600-FC-SBD

Бренды по названию

Популярные бренды