manualshive.com logo in svg

Xyratex RS-1600-FC-SBD, Инструкция по установке и эксплуатации

Поделиться
Скачать
Xyratex RS-1600-FC-SBD Скачать руководство пользователя страница 35

Getting Started

21

2.3 Enclosure Installation Procedures 

Caution

The RS-1600-FC-SBD and RS-1602-FC-SBD Enclosures with all  component parts installed are too 
heavy for easy installation into a Rack cabinet. The following procedures describe the installation of  RS-
1600-FC-SBD and RS-1602-FC-SBD enclosures and highlights any critical co-requisite requirements 
and good handling practices which we encourage you to follow so as to ensure that a successful 
installation is achieved in the easiest manner.

Warning

Ensure that you have fitted and checked a suitable anti-static wrist or ankle strap and observe all 
conventional ESD precautions when handling RS-1600-FC-SBD or RS-1602-FC-SBD modules and 
components. Avoid contact with Backplane components and module connectors, etc.

2.3.1 Pre-Requisites

The RS-1600-FC-SBD and RS-1602-FC-SBD Enclosures are designed for installation into an industry 
standard 19 inch cabinet capable of holding the unit.

• Minimum depth 500 mm from front flange to rear metalwork (excludes rear cabling).

• Weight: up to 37kg dependent upon configuration per enclosure.

• A minimum gap of 25mm (1inch) clearance between the rack cover and front of drawer; and 50mm 

(2 inches) rear clearance between rear of drawer and rear of rack is recommended in order to 
maintain the correct air flow around the enclosure.

• The rack should present a maximum back pressure of 5 pascals (0.5mm water gauge).

2.3.2 Rack Mounting Rail Kit

A set of mounting rails is available for use in 19 inch rack cabinets. These rails have been designed and 

tested to handle the maximum enclosure weight and to ensure that multiple RS-1602 enclosures may be 
installed without loss of space within the rack. Use of other mounting hardware may cause some loss of 
rack space.

The rack mounting rail kit also incorporates a rear hold down mechanism to ensure shock and vibration 
immunity. 

Please contact your supplier to ensure suitable mount rails are available for the rack you are using.

2.3.2.1

Parts Check List

• Rack Mounting Rail Kit.

2.3.2.2

Installation Procedure

Please see detail drawings supplied with the rack mounting rail kit for assembly details.

Содержание RS-1600-FC-SBD



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды