manualshive.com logo in svg

XSPC RayStorm V3 Kit, Руководство пользователя

Поделиться
Скачать
XSPC RayStorm V3 Kit Скачать руководство пользователя страница 9

Internal Radiator Layout

Top Mounted Radiator Layout

Rear Mounted Radiator Layout

Ideally your case will have room to install the radiator 
internally. This could be at the top, bottom or front of 

the case. The air should always flow out of the case.

Mounting the radiator internally won't give the best 
performance, but it's the neatest solution and we highly 

recommend using it where possible.

This layout uses the bracket set to attach the radiator 

to the rear of the case. The brackets can attach to a 
120mm or 80mm fan grill. See page 8 for details.

This method will give a better performance because of 

improved airflow through the radiator.

This layout uses the bracket set to attach the radiator 
to the top of the case. You may need to drill 4 holes in 

your case roof to secure the radiator. See page 8 for 
details.

Again this method will give a better performance 

because of improved airflow through the radiator.

Page 8/18

Содержание RayStorm V3 Kit





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды