manualshive.com logo in svg

XSPC RayStorm V3 Kit, Руководство пользователя

Поделиться
Скачать
XSPC RayStorm V3 Kit Скачать руководство пользователя страница 16

The installation process below is shown without the tubing connected. This has been done so the installation process 

can be seen clearly, without any obstructions.

Fitting the Waterblock (AMD)

1. Remove the plastic film from the base of the 
waterblock.

2. Apply a thin layer of thermal paste to the CPUs heat 
spreader.

7. Push the LEDs into either side of the waterblock.

4. Place a plastic washer and metal washer over each 

of the four posts.

3. Place the waterblock over the posts and onto the 

CPU.

5. Place a spring over each of the four posts.

6. Place a nut onto each post and gradually tighten 
them. You should tighten each nut in stages. e.g. 

1,2,3,4,1,2,3,4,1,2,3,4, until each nut is fully 
tightened.

8. The block is now ready to use. When you first boot it is 
advisable to use software to check the core temperature. 
If the temperature is high you will need to remount the 
block. 

Page 15/18

Содержание RayStorm V3 Kit





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды