XSPC RayStorm V3 Kit Скачать руководство пользователя страница 17

Страница: 17 / 20

Finishing Touches

2. Connect the fans to the motherboard fan headers,

or a fan controller.

1. Connect the tachometer output from the pump to

the motherboard fan header. This will allow you to
monitor the pumps speed. (D5 Pump only)

4. Push the 5mm LED into the LED holder and connect

the LED to the PSU.

3. Push the two 3mm LEDs into the LED holders and

connect the LEDs to the PSU.

5. The dial on the back of the pump can be used to
set the pump speed. 5 being full power and 1 being

the lowest noise level. (D5 Pump only)

6. Your system is now ready to use.

When first booting the system we

would suggest monitoring the CPU

temperature.

Attaching the Bay Pump/Reservoir

1. Push the pump back so the faceplate is flush with
the front of the case. Fix the pump in place by using

the small M3 screws.

2. If you have a case with quick release clips, we
recommend removing them and using the screw hole

underneath.

Attaching the Bay Pump/Reservoir

Page 16/18

Содержание RayStorm V3 Kit





















Результаты поиска

Содержание RayStorm V3 Kit

Отзывы:

Бренды по названию

Популярные бренды

XSPC RayStorm V3 Kit, Руководство пользователя

Результаты поиска

Содержание RayStorm V3 Kit

Отзывы:

Бренды по названию

Популярные бренды