manualshive.com logo in svg

XSPC RayStorm V3 Kit, Руководство пользователя

Поделиться
Скачать
XSPC RayStorm V3 Kit Скачать руководство пользователя страница 3

Introduction

Installation Overview

Thank you for purchasing the XSPC RayStorm WaterCooling kit. RayStorm WaterCooling 
kits provide excellent cooling performance and low noise levels. The kit is easily 

expandable, allowing you to add a GPU cooler and additional radiators.

Please read through this installation guide throughly before you start installing the kit. It's 

best to have a clear idea of how you will install the kit before you attempt installation. If 

you don't understand any part of the installation process please contact us for advice.

After the kit is setup you should leak test for at least 24 hours. While we leak test every 

component before shipping, you should still leak test it again as a precaution 

We hope you enjoy using this kit and it provides you with years of reliable service.

Disclaimer: This product is sold as a DIY watercooling kit. You are responsible for correct 

installation and maintenance of the this product. XSPC will not be held responsible for any 

loss of property/data or personal harm caused by the improper use or installation of this 

equipment. 

The components in this kit are supplied with a 12 month manufacturers warranty. This 

excludes faults caused by incorrect installation or improper use.

To improve long term reliability, we recommend the use of XSPC EC6, or ECX coolant.

Installation of the kit is split into three main sections. The first is preparation and shows 

how to prepare the motherboard, pump, radiator, and waterblock, ready for installation. 
The second is planning the layout and route for the tubing. The last section shows the 

actual installation process. We highly recommend reading the manual end to end before 

installation. It will make things easier in the long run.

This manual covers several versions of the RayStorm kit, so some steps may not be 

relevant to your kit. Wether you're using the D5 or X20 420 pump, a 120mm or 140mm 

radiator, the installation process is basically the same. Installation is relatively straight 
forward, the key is to thoughtfully plan the layout of the components and tubing. 

Preparation – Pages 3-5

Planning – Pages  6-8

Installation -  Pages 9-16

Page 2/18

Содержание RayStorm V3 Kit





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды