manualshive.com logo in svg

XSPC RayStorm V3 Kit, Руководство пользователя

Поделиться
Скачать
XSPC RayStorm V3 Kit Скачать руководство пользователя страница 12

Example Installation Walkthrough

1. Place the motherboard into the case and position 

the radiator, pump and waterblock into the chosen 
locations. You might want to try moving the 

components around to find the best positions for 
routing tubing.

2. Decide on the loop order and measure the length of 

tubing for each connection. We advise leaving 5-10cm 
of slack tubing for the connection to the pump. This will 

allow you to move the pump for filling and topping up 
the coolant.

3. Connect the tubing and check all the fittings are sealed. In the photos above the loop order is pump > radiator > CPU 

block > pump. When the tubing is connected you should make sure it doesn't have any kinks. Kinks will reduce the flow 

rate and have a significant effect on performance.

4. You can now remove the motherboard from the 

system, ready for filling and leak testing.

Attaching the Radiator

1. Lift the radiator into position and line it up with the 
screw holes on the case panel.

2. Use four 6mm 6-32 screws in each of the four 
corner holes. Do not use screws longer then 6mm.

Page 11/18

Содержание RayStorm V3 Kit





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды