background image

 

User Manual 

XProHeli Silk Gimbal

 

 

Silk Gimbal 

Page 26 

©2014 XPROHELI. All Rights Reserved.  

4.

 

XPX/XP2 Installation 

 

Overview 

Mounting the Silk to your XPX or XP2 Monster quadcopter for the 
first time requires approximately 10 minutes of time. You want to 

make sure you have a clean flat area to work in. If you are in the 
field assembling your quad you want to be consciences of not 
setting your quad upside down where there is dirt or foreign debris 
– as you do not want any unwanted items to enter the motors of 

the quad or the gimbal.  It is preferred to use a table or even the 
top side of your transport case to stage the assembly. 
 
If you plan to supply power to the Silk from your flight battery make 
sure that you are using a 3S power source. Failure to do so will FRY 

your controller. You can use up to a 5S power source (18.5v) but be 
warned that this will require you to adjust the PID power settings in 
the software. Since the XPX uses a 6S power source, a BEC or DC to 
DC down-converter must be used – otherwise you can use a 

separate 3S battery pack.  

 

Mounting to your XPX:  

Before mounting your Silk to your XPX you should have already 
gone through the Silk setup instructions above. You should know 
how to fly your quadcopter and your Silk should be operational 
and working good. Before your first flight be sure that all the active 

 

WARNING! 

 

POWER YOUR SILK 
FROM A 3S-5S(11-

18.5V) POWER 

SOURCE ONLY! NEVER 
PLUG IN A 6S POWER 

SOURCE  AS THIS WILL 

FRY YOUR 
CONTROLLER!! 

 

Содержание Silk Gimbal


















































Отзывы: