Xilinx T1 Скачать руководство пользователя страница 43

Страница: 43 / 48

Appendix B

Regulatory Compliance Statements

FCC Class A Products

The products referred to in this document are listed below:

• TA-T1-P12G-PQ-EV (encryption enabled)

• TA-T1-P12G-PQ-DV (encryption disabled)

Note: These devices are for use with UL Listed Servers or I.T.E.

Regulatory compliance statements are valid for the production version of this product; not for
engineering sample (ES) products.

Note: These products are currently certified for use in Japan only.

Safety

The following safety standards apply to all products listed in this document.

IEC 62368-1, 2nd Edition, 2014/A11:2017, Information technology equipment – Safety, Part 1:
General requirements

EN 62368-1, 2nd Edition, 2014/A11:2017, Information technology equipment – Safety, Part 1:
General requirements

UL 62368-1, 2nd Edition, 2014-12-01, Information technology equipment – Safety, Part 1: General
requirements

CSA C22.2 No. 62368-1-14, 2nd Edition, 2014-12-01, Information Technology Equipment – Safety,
Part 1: General Requirements

Appendix B: Regulatory Compliance Statements

UG1518 (v1.0) December 17, 2021

www.xilinx.com

T1 Telco Accelerator Card Installation Guide

Send Feedback

Содержание T1

















































Результаты поиска

Содержание T1

Отзывы:

Бренды по названию

Популярные бренды

Xilinx T1, Руководство по установке

Результаты поиска

Содержание T1

Отзывы:

Бренды по названию

Популярные бренды