manualshive.com logo in svg

Xilinx T1, Руководство по установке

Поделиться
Скачать
Xilinx T1 Скачать руководство пользователя страница 23

2 x 25G External SFP Test

The two 25G MAC cores are instantiated in the FPGA. The SFP ports of the T1 card are
connected using a 25G optical SFP cable. The FPGA reroutes the packets received in QDMA to
the external SFP, and then routes them from the external SFP back to QDMA. The throughput
and packet loss are then analyzed.

Test Procedure

1. Set up the system as shown in the following figure.

DPDK-Pktgen Port0

MPSoC

Host

PCIe 

X8

RFSoC

PCIe 

X8

T1 Telco Accelerator Card

Queue1_External SFP Data Path

25G SFP Cable

SFP0

SFP1

X25237-033121

2. Connect the 25G SFP cable in a loopback fashion.

3. Ensure the conditions in the 

Chapter 2: Card Information and Installation

 section have been

met.

4. Run the 

test.sh

 in root, with 

init

 as argument, to initialize the DMA and DPDK drivers.

5. Execute the 

test.sh

 script, with 

sfp

 as argument, to launch the Pktgen application with

one port.

6. Set the packet size to 1514 with the command 

set all size 1514

 inside the Pktgen

application.

7. Start the traffic with the command 

start all

 and analyze the throughput.

8. Observe the RX and TX rate and check whether there is any loss.

9. When the test is complete, stop traffic with the command 

stop all

 and then quit the test.

The expected results running the SFP test are shown below.

Chapter 6: Running the Tests

UG1518 (v1.0) December 17, 2021

 

www.xilinx.com

T1 Telco Accelerator Card Installation Guide

 23

Send Feedback

Содержание T1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды