Xilinx I2S Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 40

background image

Note

:

It is not recommended to change this value at runtime.

2. Program the SCLK Divider.

Note

:

It is not recommended to change this value at runtime.

3. Program the AES registers to specify the 192 bits of Channel Status value

4. Enable the core and latch the AES Channel bit.

Note

:

After asserting either

aud_mrst

or

m_axis_aresetn

, the core has to disabled and enabled again.

Interrupts

Each core has one interrupt output. The Interrupt output is level triggered and stays asserted
until the interrupt status bits are cleared.

Audio AXIS Interface

An AXI4-Stream audio cycle is illustrated in the following figure. The data is valid when both the
valid (TVLD) and ready (TRDY) signals are asserted. The I2S Receiver sends out adjacent channels
in sequential order (CH0, CH1, etc). Usually, the I2S Transmitter also expects the channels in
sequential order. If the channel data is not in order, then the I2S Transmitter would assert
underflow or block sync error.

Figure 4:

Audio AXIS Interface

CLK

TDATA[31:0]

TVALID

TREADY

TID[4:0]

Pre-emble = TData[3:0]

Channel Status = TData[30]

D

0

D

1

D

2

D

3

D

N

D

0

D

1

D

2

D

3

D

N

0

1

2

3

n

0

1

2

3

n

X

Y

X

Y

Y

Z

Y

Z

Y

Y

C[190]

C[191]

C[191]

C[0]

C[0]

Frame 191 (End of Block)

Frame 0 (Start of Block)

You must ensure proper pre-emble and TIDs while sending more than two channels of Audio
data over AXIS. The data width over the AXI4-Stream interface is fixed at 32-bits. All bit
positions are as per the IEC60958-3 standard except for the preamble bit format. The preamble
provides the start of the audio block and audio channel information. The preamble patterns for
the start of block, channelA audio data, and channelB audio data are listed as follows:

Chapter 4: Designing with the Core

PG308 (v1.0) April 4, 2018

www.xilinx.com

[placeholder text]

I2S Transmitter and I2S Receiver

25

Send Feedback

«
...
23
24
25
26
27
...
»

Содержание I2S









































Отзывы:

Нет отзывов

Похожие инструкции для I2S

Бренд: Sansui Страницы: 20

Бренд: Icom Страницы: 42

Бренд: Icom Страницы: 6

FT-227R Memorizer

Бренд: Yaesu Страницы: 42

Бренд: Teac Страницы: 56

Бренд: Majestic Страницы: 13

Бренд: Fisher Страницы: 12

Бренд: Aiwa Страницы: 9

Бренд: Onkyo Страницы: 40

Бренд: Sigma Страницы: 23

Бренд: Audiovox Страницы: 78

Бренд: Strong Страницы: 25

Бренд: azur Страницы: 98

Бренд: Eight Страницы: 59

Бренд: Avenview Страницы: 13

PowerTalk Head w/ADSP & SNS 04-22

Бренд: SGC Страницы: 72

Бренд: SAF Страницы: 64

Бренд: DigiTech Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды