Xerox 770 Скачать руководство пользователя страница 236

Страница: 236 / 268

Recommended solution

Possible cause

Fault code

Reset the paper or cancel the job.

Designated paper size and
the size of paper in the
tray differs when feeding
paper

024 974

Check staples and reset correctly.

Finisher staple fault

024 976

Check staples and reset correctly.

Finisher staple feeding is
not ready

024 977

Check staples and reset correctly.

Booklet Finisher staple
operation is not ready

024 978

Check staples. Follow procedures to
remove and replace staple cartridge.

The staple cartridge is
empty

024 979

Remove all paper from the stacker
tray.

The finisher stacker tray is
full

024 980

Remove all paper from the finisher
top tray.

The finisher top tray is full

024 981

Remove all paper from the stacker
tray and remove any other
obstructions.

The finisher stacker tray
lower safety warning in on

024 982

Remove all paper from the booklet
tray.

The finisher booklet tray is
full

024 983

Remove all paper from the booklet
tray.

The booklet stapler low
staple F signal is on

024 984

Remove all paper from the booklet
tray.

The booklet stapler low
staple R signal is on

024 985

Remove all paper from the tray. Set
the output tray for three fold.

The booklet folder tray is
full

024 987

Check that the folder tray is correctly
attached and set.

The booklet folder tray is
full

024 988

Check the staple cartridge and reset
correctly.

There is a problem with
the booklet maker stapler

024 989

Power Off/On the machine. If the
error persists, contact the Customer
Support Center.

A communication error has
occurred with the Finisher

047 320

Remove and empty the waste
container and reinstall.

Punch Waste Container is
full or near full

112 700

Confirm the staple psoition and try
to print again.

The settings for stapling
are canceled and prints the
data

116 790

Confirm the punching position and
try to print again.

The settings for punching
are canceled

124 705

Confirm the folding settings and try
to print again.

The settings for folding are
canceled

124 706

Xerox

770 Digital Color Press

16-38

User Guide

Standard/Booklet Maker Finisher

(continued)

Содержание 770













































































































































































































































































Результаты поиска

Содержание 770

Отзывы:

Xerox 770, Руководство пользователя, Страница: 236 / 268

Результаты поиска

Содержание 770

Отзывы: