Xerox 770 Скачать руководство пользователя страница 229 | Manualshive

Страница: 229 / 268

Xerox 770 Скачать руководство пользователя страница 229

4. Close the Right Cover on the finisher.

Note

A message will display and the machine will not operate if the right cover is open
even slightly.

Stapler faults

Follow the procedures provided when the output is not stapled or the staples are bent.
Contact our Customer Support Center if the problem persists after you have tried the
following solutions. Stapler faults on output may look similar to the ones shown in the
following illustration.

1. No staple

2. Bent staple

3. One side of staple rising up

4. Staple bent in reverse direction

5. Flattened staple

6. Entire staple rising up

7. Staple rising up withcenter pressed in

If the output is stapled as shown in the figure above, contact our Customer Support
Center.

Note

Depending on the type of paper that is being stapled, the stapled nails may be bent. If
the bent nails are stuck inside the machine, they may eventually cause paper jams.
Remove the bent staple when opening the staple cartridge cover. If you do not remove
the bent staple, a staple jam may occur as a result. Use the staple cartridge cover only
when removing the bent staple.

16-31

Xerox

®

770 Digital Color Press

User Guide

Standard/Booklet Maker Finisher

«
...
227
228
229
230
231
...
»

Содержание 770













































































































































































































































































Отзывы:

Нет отзывов