manualshive.com logo in svg

Xcel-Arc RAZORWELD 205, Руководство по эксплуатации, Страница: 14 / 52

Поделиться
Скачать
Xcel-Arc RAZORWELD 205 Скачать руководство пользователя страница 14

14

 |    

RAZORWELD™ 205SS MIG/TIG/STICK Welder Manual

GAS INSTALLATION & SET UP - MIG

(9)   Align the wire into the groove of the drive roller and close down the top roller making sure the wire is in the 

  

groove of the bottom drive roller, lock the pressure arm into place. Apply a medium amount of pressure to the

 

 

drive roller

(10)

  Remove the gas nozzle and contact tip from the torch neck,

(11)

  Press and hold the inch button to feed the wire through to the torch neck, release the inch button when the wire 

 

 

exits the torch neck.

 

(12)

  Fit the correct sized contact tip and feed the wire through it, screw the contact tip into the tip holder of the torch

 

 

head and nip it up tightly. 

(13)  Fit the gas nozzle to the torch head. 
(14)  

Carefully open the gas cylinder valve and set the flow rate to between 8-12 l/min.

 

(15)  Select 2 or 4 time trigger function.
(16)  Select the MIG Smart Set program to suit the wire diameter and gas type being used.
(17)  

Select the wire feed speed required to suit the material thickness being welded, it will show on the digital meter

 

 

as m/min. Increasing the wire feed speed increases the welding amperage output - Smart Set will adjust the 

 

Voltage to suit automatically, always providing a smooth arc.  Smart Set permits fine tuning of the voltage 

 

 

allowing you to personally customise your setting. 

(10) Remove the gas nozzle and contact tip 
from the front end of the mig torch. 

(12) Fit the correct size contact tip over 
the wire and fasten tightly into the tip 
holder.

(13) Fit the gas nozzle to the torch head.

(15) Select torch switch mode 2T or 4T

(16) Select your preferred Smart Set 
program selection

(17) Set welding amperage using the wire feed 

knob, increasing the wire feed increase the 

amperage. Fine tune if required using the voltage 
knob. 

(9) Close down the top roller bracket and clip 
the pressure arm into place with a medium 
amount of pressure applied.

(14) Carefully open the valve of the gas 

cylinder, set the  flow to 10 l/min

(11) Press and hold the inch wire button to 
feed the wire down the torch cable through 
to the torch head.

Содержание RAZORWELD 205





















































Отзывы:

Нет отзывов