Xcel-Arc RAZORWELD 205 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 52

Xcel-Arc RAZORWELD 205 Скачать руководство пользователя страница 13

RAZORWELD™205SS MIG/TIG/STICK Welder Manual

|

13

Razor

Weld

GAS INSTALLATION & SET UP - MIG

(5) Connect the gas regulator to the gas
cylinder and tigthen. Connect the gas
line to the gas regulator.

Caution:

Disconnect the Electrode Holder cable from the machine before using MIG function. If cable is not disconnected welding
voltage is present and can cause Arcing or Flash.

(1) Select Standard using the Standard/Spool Gun selector switch.
(2) Insert the earth cable plug into the negative socket on the front of the machine and tighten it.

(3)

Plug the welding torch into the Euro Mig torch connection socket on the front panel, and tighten it.

IMPORTANT : When connecting the torch be sure to tighten the connection. A loose connection can

result in the connector arcing and damaging the machine and gun connector.

This damage is not covered under warranty.

(4)  Connect Weld Power Lead to the Positive terminal
(5)  Connect the gas regulator to the Gas Cylinder and connect the gas line to the Gas Regulator. Check for Leaks!
(6)  Connect the gas line to the machine via the quick push lock connector located on the rear panel. Check for Leaks!

(7) Place the Wire Spool onto the Spool Holder. Snip the wire from the spool being sure to hold the wire to prevent

rapid uncoiling. Feed the wire into the wire feeder inlet guide tube through to the drive roller.

(8)

Carefully feed the wire over the drive roller into the outlet guide tube, feed through about 150mm into the torch

receptacle. Check that the drive roller size is compatible with the wire diameter, replace the roller if necessary.

(7)

Place wire onto spool holder - (spool retaining

nut is left hand thread ) Feed the wire through the

inlet guide tube on to the drive roller.

(8) Feed wire over the drive roller into

the outlet guide tube, Push the wire

through approx 150mm.

(2) Connect the earth
lead to the terminal

(1) Set Standard/Spoolgun
selector switch inside door
to Standard

IMPORTANT :

When connecting the

torch be sure to tighten the connection.

(3) Connect Mig torch

(4) Connect the Weld Power lead
to the terminal

IMPORTANT
Select the correct polarity. Connect the weld
power lead to output terminal.

(6) Connect the gas line to the machine
inlet gas connector via the quick push
lock connector located on the rear panel

«
...
11
12
13
14
15
...
»

Содержание RAZORWELD 205





















































Отзывы:

Нет отзывов