Xcel-Arc RAZORWELD 205 Скачать руководство пользователя | Manualshive

Страница: 29 / 52

background image

RAZORWELD™205SS MIG/TIG/STICK Welder Manual

|

29

Razor

Weld

INSTALLATION SET UP FOR

DC TIG WELDING

(1) Connect the Tig torch to the Euro connection on the front of the machine and tighten it.

IMPORTANT : When connecting the torch be sure to tighten the connection

(2)  Insert the earth cable plug into the Positive socket on the front of the machine and tighten it.
(3)  Insert the weld power cable plug into the Negative socket on the front of the machine and tighten it.
(4)  Connect the gas line of the Tig torch to regulator and connect the regulator to the gas cylinder.
(5)  Connect the gas line to the machine via the quick push lock connector located on the rear panel.
(6)

Open the gas valve cylinder slowly and set the flow rate for 12 l/min.

(7) Select TIG functionon the front panel.

Set torch operation 2T / 4T.

• When 2T operation is selected press trigger Gas starts, touch and lift arc start, release trigger Gas and Arc stops.

• When 4T operation is selected press and release trigger Gas starts, touch and lift arc start, press and release

trigger Gas and Arc stops.

(4) Connect the gas line to the regulator

and connect to the gas cylinder

IMPORTANT :

When connecting the

torch be sure to tighten the connection.

(1) Connect the TIG torch

(3) Connect the Weld Power lead
to the terminal

(2) Connect earth lead

to the terminal

(7)

Select TIG function, 2T, 4T Trigger as

required

(6) Carefully open the valve of the gas

cylinder, set the flow to 6-10 l/min

(5) Connect the gas line to the machine
inlet gas connector via the quick push
lock connector located on the rear panel

IMPORTANT
Select the correct polarity. Connect the weld
power lead to output terminal.

«
...
27
28
29
30
31
...
»

Содержание RAZORWELD 205





















































Отзывы:

Нет отзывов

Похожие инструкции для RAZORWELD 205

Бренд: DAB Страницы: 8

Бренд: Neets Страницы: 16

Wisenet SNK-B73040BW

Бренд: Samsung Страницы: 16

Бренд: Eastwood Страницы: 12

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 4

Бренд: Eastwood Страницы: 12

Бренд: Easy Clocking Страницы: 23

Бренд: Handicare Страницы: 20

Бренд: Yamaha Страницы: 40

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 3

Бренд: MAC TOOLS Страницы: 30

PLASMA CUTTING Series

Бренд: Vector Welding Страницы: 56

HiFi Speaker System

Бренд: Eltax Страницы: 2

TripleShield C2S6

Бренд: HOME8 Страницы: 6

Бренд: Air Liquide Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды