manualshive.com logo in svg

Xantrex Freedom X 1200 120VAC, Руководство пользователя

Поделиться
Скачать
Xantrex Freedom X 1200 120VAC Скачать руководство пользователя страница 71

975-0767-01-01

57

Troubleshooting Reference

No output voltage. The status LED is red.

AC shore power is not available or out of operating range and the inverter has shut down with the LCD 
screen showing one of the following error codes:

•

Low input voltage (fault code 



)

•

Check the DC connections and the cable.

•

Recharge the battery.

•

High input voltage (fault code 



) •

Verify the unit is connected to a 12V battery.

•

Check the voltage regulation of the external charging 
system (if any).

•

Unit overload or AC output short 
circuit (fault code 



)

•

Reduce the load. Make sure the load does not exceed the 
output rating.

•

Thermal shutdown (fault code 



) •

Allow the unit to cool off.

•

Reduce the load if continuous operation is required.

•

Improve ventilation. Make sure the inverter’s ventilation 
openings are not blocked.

Table 7 

Troubleshooting Reference

Problem

Possible Cause

Solution

Freedom X Owners Guide.book  Page 57  Wednesday, May 11, 2016  10:32 AM

Содержание Freedom X 1200 120VAC















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды