manualshive.com logo in svg

Xantrex Freedom X 1200 120VAC, Руководство пользователя

Поделиться
Скачать
Xantrex Freedom X 1200 120VAC Скачать руководство пользователя страница 15

975-0767-01-01

1

Introduction

The Freedom X Sine Wave Inverter (Freedom X) is designed with 
integrated inverting functions and power management features 
suitable for marine, recreational, and commercial vehicle 
installations.
Please read this chapter to familiarize yourself with the main 
performance and protection features of the Freedom X.

Materials List

The Freedom X

 

base package includes the following items:

•

one Freedom X unit

•

one Owner’s Guide and extra safety labels

•

one set of pre-installed M8 DC terminal nuts (not shown)

•

one DC ground box lug

NOTE

: If any of the items are missing, contact Xantrex or any 

authorized Xantrex dealer for replacement. See “Contact 
Information” on page i.

Figure 1 

What’s In The Box

Display panel

Product image shown may 
vary from actual product.

Owner’s Guide 
and extra labels

Freedom X unit

Ow

ner

’s G

uide

DC ground 
box lug

Freedom X Owners Guide.book  Page 1  Wednesday, May 11, 2016  10:32 AM

Содержание Freedom X 1200 120VAC















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды