Xantrex Freedom SW 815-2012 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 78

background image

iv

Freedom SW Installation Guide

Important Safety Instructions

IMPORTANT:

R

EAD

AND

SAVE

THIS

I

NSTALLATION

G

UIDE

FOR

FUTURE

REFERENCE

.

This chapter contains important safety and installation instructions for the
Freedom SW Inverter/Charger (Freedom SW). Each time, before using the
Freedom SW, READ ALL instructions and cautionary markings on or
provided with the inverter/charger, the batteries, and all appropriate sections
of this guide.

NOTE:

The Freedom SW contains no user-serviceable parts. See “Warranty

and Return Information” on the Owner’s Guide for guidance.

NOTE:

Turning off the inverter/charger using the on/off switch on the front

panel will not reduce an electrical shock hazard.

ELECTRICAL SHOCK HAZARD

•

Do not expose the Freedom SW to rain, snow, spray, or bilge water.
This inverter/charger is designed for marine applications only when
additional drip protection is installed in certain orientations. See the
installation guide for information.

•

Do not operate the inverter/charger if it has received a sharp blow,
been dropped, has cracks or openings in the enclosure including if the
fuse cover has been lost, damaged, or will not close, or otherwise
damaged in any other way.

•

Do not disassemble the inverter/charger. Internal capacitors remain
charged after all power is disconnected.

•

Disconnect both AC and DC power from the inverter/charger before
attempting any maintenance or cleaning or working on any circuits
connected to the inverter/charger. See note below.

•

Do not operate the inverter/charger with damaged or substandard
wiring. Make sure that all wiring is in good condition and is not
undersized.

Failure to follow these instructions will result in death or serious
injury.

Freedom SW 3K2K InvChg Install Guide.book Page iv Wednesday, October 12, 2011 4:40 PM

«
...
4
5
6
7
8
...
»

Содержание Freedom SW 815-2012















































































Отзывы:

Нет отзывов

Похожие инструкции для Freedom SW 815-2012

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: Danfoss Страницы: 292

Бренд: Lumantek Страницы: 14

Бренд: YASKAWA Страницы: 67

Бренд: N-Tron Страницы: 2

Бренд: Nagra Страницы: 18

Бренд: Hagstrom Страницы: 24

GTV-192KUSB-2-ADAUD

Бренд: GefenTV Страницы: 36

Бренд: Radial Engineering Страницы: 11

Бренд: DX Engineering Страницы: 4

ProView PVR-8140

Бренд: Harmonic Страницы: 2

Бренд: Generac Power Systems Страницы: 150

Бренд: Metra Electronics Страницы: 3

Бренд: Phrontier Technologies Страницы: 16

60 WATT SOLAR 12 VOLT POWER GENERATOR KIT

Бренд: Sunforce Страницы: 14

Бренд: All-Power Страницы: 53

Бренд: Albatross Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды