Xantrex Freedom SW 815-2012 страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 78

background image

97-0020-01-01

41

Installing the Inverter/Charger

This

g

u

id

e for

u

se by qu

alifi

ed installers only.

Step 8: Testing Your Installation

There are several tests to be performed for testing your installation. These
tests will verify that:

•

the Freedom SW works in invert mode,

•

the Freedom SW works in charge mode, and

•

the Freedom SW works in AC bypass mode.

If the test fails at any point, go to “Step 7: Performing Checks Prior to
Initial Start-Up” on page 40 and go through the checklist again to check the
installation. Then perform the test again. If the test fails again, see the
troubleshooting section in the Freedom SW Sine Wave Inverter/Charger
Owner’s Guide.

Testing in Invert Mode

To test the Freedom SW in invert mode, using a 100 watt light bulb as
the test load:

1.

Close the DC disconnect switch or the DC circuit breaker to supply
DC power to the Freedom SW.

Wait for all the lights on the front panel to flash on and off, indicating
that the unit has successfully initialized (10 to 30 seconds).

If the light does not come on, make sure the voltage at the DC
terminals on the Freedom SW is correct, as described in “Step 7:
Performing Checks Prior to Initial Start-Up” on page 40.

ELECTRICAL SHOCK HAZARD

The Inverter Enable button on the Freedom SW and the optional
accessories do not disconnect DC or AC input power to the Freedom SW.

Failure to follow these instructions can result in death or serious
injury.

Figure 16

Freedom SW Front Panel

XANBUS INTERFACE

STACKING

FREEDOM

SW

INVERTER/CHARGER

CLEAR FAULT

RESET

INVERTER
ENABLE

INVERTER
ENABLED

AC IN

FAULT

GEN

SUPPORT

CHARGING WARNING

Freedom SW 3K2K InvChg Install Guide.book Page 41 Wednesday, October 12, 2011 4:40 PM

«
...
53
54
55
56
57
...
»

Содержание Freedom SW 815-2012















































































Отзывы:

Нет отзывов

Похожие инструкции для Freedom SW 815-2012

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 9

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 7

Бренд: BARIX Страницы: 4

GUARDIAN SERIES

Бренд: Generac Power Systems Страницы: 12

Бренд: QUAD Страницы: 2

DCS SCARLATTI DAC

Бренд: Data Conversion Systems Страницы: 26

Бренд: Harman Kardon Страницы: 16

Бренд: Datavideo Страницы: 13

ServeMaster 1600MV

Бренд: IBC SOLAR Страницы: 58

Бренд: Airpax Dimensions Страницы: 6

Бренд: RadioLink Страницы: 11

IP4K-500 Series

Бренд: Altimium Страницы: 38

Бренд: TRUELOOK Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды