Xantrex Freedom SW 815-2012 Скачать руководство пользователя | Manualshive

Страница: 56 / 78

background image

42

Freedom SW Installation Guide

Installing the Inverter/Charger

2.

After initialization, observe that none of the lights on the front panel

should remain illuminated.

3.

Press the Inverter Enable button. Verify that:

•

The Inverter Enable button light illuminates,

•

The Invert On light illuminates.

4.

Connect the Freedom SW to the test load by closing the AC breaker
that controls the circuit that the test load is connected to.

If the light bulb illuminates, the Invert mode is working.

5.

Press the Inverter Enable button to disable the inverter.

The Invert On light and Inverter Enable button light are off.

Testing in Charge Mode and AC Bypass Mode

1.

Close the AC supply breaker to supply AC power to the unit.

To verify that the Freedom SW starts charging:

2.

After a few seconds, verify that the AC/Charge light on the front panel
is turned on (indicating that the batteries are being charged).

To verify that Freedom SW correctly switches to Bypass mode:

3.

Disable the AC source and turn off the inverter by pressing the Inverter
Enable button.

4.

Connect the test load to the AC output connection of the unit.

5.

Enable the AC source and the test load should turn on after ten
seconds.

Installation Complete

Your installation is now complete. The inverter/charger is ready for use.

The preceding tests use a light test load (a light bulb) as a test case. If you
encounter problems when using a load over 1000 watts (for example, a hair
dryer or microwave), see the troubleshooting information in the Freedom
SW Sine Wave Inverter/Charger Owner’s Guide.

Freedom SW 3K2K InvChg Install Guide.book Page 42 Wednesday, October 12, 2011 4:40 PM

«
...
54
55
56
57
58
...
»

Содержание Freedom SW 815-2012















































































Отзывы:

Нет отзывов

Похожие инструкции для Freedom SW 815-2012

Бренд: TAD Страницы: 128

Бренд: Xantrex Страницы: 76

Бренд: Perlight Solar Страницы: 19

Бренд: Sima Страницы: 2

Бренд: Alca Power Страницы: 8

Бренд: Transition Networks Страницы: 13

COM-K IMR01Z01-E9

Бренд: RKC INSTRUMENT Страницы: 2

Бренд: Trace Engineering Страницы: 2

Бренд: C2G Страницы: 263

Бренд: Baumer Страницы: 41

Бренд: Yuan Страницы: 15

Autotransformer MW 1700

Бренд: Fronius Страницы: 15

Бренд: BZBGEAR Страницы: 12

Бренд: Solax Страницы: 3

Бренд: ADF Web Страницы: 31

Бренд: Velleman Страницы: 11

Бренд: Leader Electronics Corp. Страницы: 13

CoolSET ICE2QR 65 Series

Бренд: Infineon Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды