manualshive.com logo in svg

Xantrex Freedom SW 815-2012, Руководство по установке

Поделиться
Скачать
Xantrex Freedom SW 815-2012 Скачать руководство пользователя страница 46

32

Freedom SW Installation Guide

Installing the Inverter/Charger

Connecting the DC Cables to the Inverter/Charger

To connect the DC cables:

1.

Route the DC cables from the battery bank to the inverter/charger. 
Observe the “Guidelines for Routing the DC Cables” on page 31.

2.

Install a DC fuse and disconnect switch or a DC circuit breaker 
between the inverter/charger and the battery. It must be installed in the 
positive side of the DC circuit, as close as possible to the battery.

This protects your battery and wiring in case of accidental shorting. 
See Table 4 on page 17 for required fuse or breaker size. 

3.

Open the DC disconnect switch or turn off the DC circuit breaker.

4.

Connect one connector on the POSITIVE (+) cable to the POSITIVE 
DC terminal on the inverter/charger, as shown in Figure 8. The 
connector goes on first, then the flat washer (steel), lock washer 
(steel), and 3/8" bolt (brass).

5.

Connect the other connector to the POSITIVE (+) terminal on the fuse 
or breaker. Observe polarity carefully while completing the 
installation.

Use a wrench to tighten the bolt to a torque of 15–16 ft-lbs 
(20.4–21.7 Nm) at the inverter/charger end. Observe the fuse holder or 
breaker manufacturer’s recommendation at the other end.

6.

Connect one connector on the NEGATIVE (–) cable to the 
NEGATIVE (–) DC terminal on the inverter/charger, as shown in 
Figure 8. The connector goes on first, then the flat washer (steel), lock 
washer (steel), and 3/8" bolt (brass).

FIRE HAZARD

Use only appropriately sized copper cable. Loose connections, improper 
connections, and under-rated cables will overheat. Make sure the bolts 
supplied by Xantrex on the inverter/charger are tightened to a torque of 
15–16 ft-lbs (20.4–21.7 Nm). Torque all other connections to the 
manufacturer’s specifications. Make sure the DC cable, washers, and bolt 
are assembled in the order shown in Figure 8.

Failure to follow these instructions will result in death or serious 
injury.

EQUIPMENT DAMAGE DUE TO REVERSE POLARITY

Before making the final DC connection or closing the DC breaker or 
disconnect, check cable polarity at both the battery and the inverter/
charger. Positive (+) must be connected to positive (+). Negative (–) must 
be connected to negative (–).

Failure to follow these instructions can damage the unit and/or 
damage other equipment.

Freedom SW 3K2K InvChg Install Guide.book  Page 32  Wednesday, October 12, 2011  4:40 PM

Содержание Freedom SW 815-2012















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды