Xantrex Freedom SW 230V 815-3524-02 Скачать руководство пользователя страница 45

Страница: 45 / 104

975-0696-01-01

Operating the Freedom SW with the SCP

Line 3

Label

Battery

Field 2

: Total battery current. Negative value if the battery is

discharging and positive value when charging.

Field 3

: Battery voltage

Field 4

: Battery temperature. Displays the highest temperature when

reading multiple inverters that are installed. Displays

N/A

when

there is no BTS attached.

Line 4

Label

Load

Field 5

: Total power drawn by AC loads connected to the unit.

Field 6

: Inverter output voltage at load terminals of one inverter/

charger unit.

Field 7

: Sum of all current drawn out by the AC loads.

Line 5

Label

AC In

Field 8

: AC input voltage at AC In terminals of the inverter/charger.

Field 9

: Sum of all current drawn into one inverter/charger unit.

Field 10

: AC input frequency

STBY/ON Fault
Clear

button

Press momentarily to clear all faults on all devices on the network.
Press and hold for five seconds to switch all devices in the network
between operating and safe modes.

Enter

Up arrow

Down arrow

buttons

(pressed
simultaneously)

Switches between Basic Settings and Advanced Settings.

Table 3

Device Setup Screen Status Information

FSW 230V Owners Guide.book Page 31 Tuesday, August 7, 2018 9:38 AM

Содержание Freedom SW 230V 815-3524-02









































































































Результаты поиска

Содержание Freedom SW 230V 815-3524-02

Отзывы:

Xantrex Freedom SW 230V 815-3524-02, Руководство пользователя, Страница: 45 / 104

Результаты поиска

Содержание Freedom SW 230V 815-3524-02

Отзывы: