manualshive.com logo in svg

Xantrex Freedom SW 230V 815-3524-02, Руководство пользователя, Страница: 27 / 104

Поделиться
Скачать
Xantrex Freedom SW 230V 815-3524-02 Скачать руководство пользователя страница 27

975-0696-01-01

13

Freedom Inverter/Charger Operation

Start Up Behavior

When the Freedom SW 230V is powered up or has been reset, all of 
the front panel lights illuminate and remain on for a minimum of 
five seconds. During this interval, the fans are also turned on as the 
unit executes internal diagnostics.
The Freedom SW 230V inverter is disabled every time the unit is 
powered up. After power up, the 

INVERTER ENABLE

 button (or 

the SCP) can be used to enable or disable the inverter. 
When a function is enabled, it is allowed to occur but other 
conditions may have to be met before the function is activated or 
turned on. For example, the charger function on the Freedom SW 
230V may be enabled, but it will not charge unless qualified AC 
power is present.

IMPORTANT: 

Review the “Important Safety Instructions” on page iii

before operating the inverter/charger.

FSW 230V Owners Guide.book  Page 13  Tuesday, August 7, 2018  9:38 AM

Содержание Freedom SW 230V 815-3524-02









































































































Отзывы:

Нет отзывов