X-Rite 891 Скачать руководство пользователя страница 64

Страница: 64 / 80

S E C T I O N E I G H T

8-4

REPLACING THE READ LAMP

(PART NUMBER 880-07)

NOTICE:

New lamp may appear bent,

DO NOT

attempt to straighten.

1. Remove four screws 1 securing the bottom cover 2 with a phillips-head

screwdriver. Leave bottom cover 2 on unit.

2. Holding top 3 and bottom 2 covers in place, turn unit over so it rests on

the bottom cover 2. Remove top cover 3.

3. Locate optics assembly 4 and remove screw and washer 5 in the middle

of lamp assembly P.C.B. 6.

4. Lift out old lamp assembly 6 and discard.
5. Install new lamp assembly 6 by carefully inserting lamp 6 into housing 7

and lamp pins 8 into lamp connector. Press down gently to make sure
connector pins 8 are properly seated.

6. Secure lamp screw and washer 5 in place.
7. Carefully clean any dust or plastic chips off circuit board and top cover 3



using moisture free compressed air. Place top cover back on instrument.

8. Holding top and bottom covers in place, turn unit over so that it rests on

top cover 3.

9. Remove bottom cover 2. Clean circuit board and bottom cover 2 with

compressed air, then place bottom cover 2 back on instrument.

10. Secure bottom cover 2 to instrument with four screws 1 using a phillips-

head screwdriver.

Содержание 891

















































































Результаты поиска

Содержание 891

Отзывы:

Похожие инструкции для 891

Бренды по названию

Популярные бренды

X-Rite 891, Руководство по эксплуатации

Результаты поиска

Содержание 891

Отзывы:

Похожие инструкции для 891

Бренды по названию

Популярные бренды