background image

20

Flip the toggle switch to start the pump. Allow the water 

to flow through the open nozzle bodies until the lines are 

flushed. Turn the pump off and close the boom ball valve.

Remove the nozzle cap from the spray gun wand. Start 

the pump and squeeze the hand spray gun trigger. Allow 

water to flow through the gun to flush those lines. Turn the 

pump off and replace the nozzle cap. Set the nozzle at the 

desired angle as the nozzle cap is tightened. 

Figure D5 

Hand Spray Gun Nozzle

Nozzle Cap  >

Do not point the spray hand gun toward any 

person or body part. The chemical and/or spray 

pressure can cause serious or fatal injuries.

Always wear protective clothing, i.e. apron, face shield, 

gloves and respirator, when handling any chemicals. 

Failure to do so will risk chemical exposure to your 

body resulting in sickness, injury or possibly death.

Install the tips, screens and caps as shown in Fig. D6. The 

cap snaps into place with a quarter turn which aligns the 

spray tip. The tip screen is the final filter before the fluid 

passes through the tip. If a single nozzle does not spray 

a proper pattern, the tip screen should be checked and 

cleaned. 

Figure D6

Installing Tips and Screens

LGT-25 Operation

L&G Operation

Add the desired amount of water or fertilizer to the sprayer 

tank. Add the correct amount of chemical to the sprayer 

tank. Read the instructions on the chemical container for 

details regarding the proper amount of chemical to add.

Hand Spray Gun Operation

To  operate  the  hand  spray  gun,  unroll  the  hand  spray 

gun hose from the tank wrap. With the boom ball valve 

turned  “Off”  (valve  handle  perpendicular  to  the  hose), 

flip the toggle switch on to start the pump. The pump will 

operate until the system pressures up to 60 psi, then will 

automatically shut off. 

Point the hand spray gun in the direction of the area to be 

sprayed and squeeze the trigger. 

Follow chemical label directions for proper application of 

the specific chemical.  

 

Figure D7

Operating Hand Spray Gun

Содержание Defender 3 Pt Sprayer



































Отзывы: