WPI UltraMicroPump II Скачать руководство пользователя страница 8

Страница: 8 / 32

UltraMicroPump II

World Precision instruments

G = Grouped

N = Non-grouped

D = Disabled

World Precision

Instruments

MicroSyringe Pump Controller

Output 1

Output 2

Output 3

Output 4

VOLUME

SET

(nl)

VOLUME

COUNTER

(nl)

RATE

DEVICE TYPE

1 2 3

4 5 6

7 8 9

SELECT

DATA

SAVE

RUN

STOP

I = Infuse

W = Withdraw

S = nl/sec

M = nl/min

Arrow keys:

Move the cursor
around the display.

Numeric keypad:

Use these keys to

enter settings for infusion and withdrawal
rates and volumes.

Select:

Toggles

the selected
parameters: Infuse/
Withdraw, Syringe
Size, Rate Units
(nL/sec or nL/min),
and mode (Grouped,
Non-grouped and
Disabled).

Run/Stop:

Starts

and stops the
pump(s).

Data Save:

Saves all parameters on LCD display

to memory. Next time the Ultra Microsyringe Pump
controller is turned on, the last paramaters saved will
be displayed.

Lights:

When a

pump is running,
the correspond-
ing light is on. For
example, the light
next to output 1 will
be on when pump
one is operating.

Fig. 4 — Micro4
front panel

Setting Parameters

Parameters are entered using the membrane keys on the front panel of the micro4.
the

left

and

right

arrow

keys move the cursor on the lcd display to the desired

position. the

and

down

arrow

keys select the channel (corresponding to the

output channels on the rear of the instrument). the

number

keys and the

select

key are used to change parameters.

Содержание UltraMicroPump II

































Результаты поиска

Содержание UltraMicroPump II

Отзывы:

Бренды по названию

Популярные бренды

WPI UltraMicroPump II, Инструкция по эксплуатации

Результаты поиска

Содержание UltraMicroPump II

Отзывы:

Бренды по названию

Популярные бренды