manualshive.com logo in svg

WPI UltraMicroPump II, Инструкция по эксплуатации

Поделиться
Скачать
WPI UltraMicroPump II Скачать руководство пользователя страница 5

UltraMicroPump II

World Precision instruments

3

Fig. 2 — Initial syringe clamp adjustment — 

Secure syringe by sequentially 

adjusting set screws with supplied Allen key:  

1

 for horizontal alignment, 

2

 for 

vertical alignment, and 

3

 to eliminate play.

Axial Needle Alignment

in order to maintain a good syringe needle alignment particularly along the same 
axis of the supporting bar, rotate the syringe body while placing in the two clamps 
to allow the syringe to seat properly and align along the body of the pump for 
minimal slant offset. if the clamp which holds the syringe collar (see “collar stop” 
in the drawing below) is too tight or too loose, syringe needle alignment may be off 
because of stress.

if the collar stop is too tight to allow the syringe collar to insert easily, then follow 
these instructions: 

immediately below and behind the collar stop, in the groove where the long drive 
screw is, there is a small Phillips head screw, attached to the collar stop. loosen 
this screw to slightly (about 0.5 to 1 mm) to allow for a thicker collar (see Fig 2). 
You may have to grasp the collar stop and wiggle it backwards to move it. once 
the stop is backed out; check and adjust for a tight fit so the syringe body doesn’t 
move when placed into the holder. Gently re-tighten the screw in the new position. 

Note:

 you may have to retract the plunger button holder to get access to the set-

screw.

Mount the pump

the ultramicroPump can 
be mounted directly onto 
a stereotaxic frame or a 
micromanipulator, using 
the mounting bar (see 
Fig. 2). the mounting bar 
may be unscrewed and 
modified by the user, if 
necessary. 

MOUNTING BAR 

COLLAR 

STOP 

SYRINGE 

COLLAR 

SET SCREW 

(not visible in this view) 

PLUNGER 

RETAINING 

SCREW 

PLUNGER BUTTON

PLUNGER 

BUTTON 

HOLDER 

CABLE CONNECTS

TO REAR PANEL OF

MICRO4 CONTROLLER

SYRINGE

CLAMPS

CLAMP
RELEASE

SET
SCREWS

SYRINGE 

1

2

3

Содержание UltraMicroPump II

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды