manualshive.com logo in svg

WPI UltraMicroPump II, Инструкция по эксплуатации

Поделиться
Скачать
WPI UltraMicroPump II Скачать руководство пользователя страница 20

UltraMicroPump II

World Precision instruments

18

Computer Control

rs232 commands are used to control the micro4 via the serial port of a Pc or 
macintosh computer.

RS232 Commands

 

All commands are case sensitive. the settings for the rs232 port are baud rate 
9600, 8 data bits, 1 start bit, 1 stop bit. microsoft Hyperterminal setting: Flow con-
trol must be set to none.

numbers and decimal points are indicated below by the “

#

” symbol.

 

V######;

  sets the delivered volume. number must have a decimal point and 

terminate with “

;

” (semicolon) — see page 19.

 

C######;

  sets the volume counter. number must have a decimal point and 

terminate with “

;

” (semicolon) — see page 19.

 

R####;

  sets the delivery rate. number must have a decimal point and 

terminate with “

;

” (semicolon) — see page 19.

 

I

  infuse mode.

 

W 

Withdraw mode.

 

G

  Go — starts the syringe pump.

 

H

  Halt — stops the syringe pump.

 

S

  sets the rate units to nanoliters/second.

 

M

  sets the rate units to nanoliters/minute.

 

L#;

  line number — sets the syringe number on display (micro4 only).

 

N

  not Grouped mode.

 

P

  Grouped mode.

 

D

  disabled mode.

 

T

x

  syringe type. the letter indicating syringe type follows the t. For 

example, to select syringe type “A” the command is “tA”.

RS232 Query Commands

All query commands begin with a question mark. Below is a list of the query 
commands.

?V

  returns the set volume.

?C

  returns the volume counter

?R

  returns the delivery rate

Содержание UltraMicroPump II

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды